A Ray's company - serving Enterprise, NV

Rheem Heat Pump Service in Enterprise, NV

Heat pumpsHeat pumps
AC repairAC repair
Furnace & heatingFurnace & heating
Ductless mini splitsDuctless mini splits
CarrierCarrier
TraneTrane
GoodmanGoodman
Every visit starts with

Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed

We have financing partners for your new heating and cooling system*On approved credit; ask us about your options

Diagnosis first, numbers second - you approve the repair price before a single part goes in.

Get your free estimate

Rheem Heat Pump Service: The Enterprise Owner’s Guide

We service and replace Rheem heat pump components in Enterprise, and most part swaps land between $150 and $650 installed depending on what failed. Same-day availability is the norm on weekdays when we have the part and the weather isn’t burying us. Ray answers the phone himself, so you’ll know before lunch whether it’s a capacitor, a contactor, a reversing valve solenoid or something else.

Call (844) 455-2034

Here’s how this usually starts. A Rheem owner in Enterprise notices the outdoor unit humming but the house not cooling, or the heat pump running nonstop in July and still losing ground. Maybe the thermostat reads 82 while the setpoint says 76. Sometimes it’s a hard stop: the breaker trips, or the compressor won’t kick on at all. That’s the moment people start looking up parts, and that’s the moment this page is for.

Ray’s Heating & Air Enterprise is an independent service provider. We’re not Rheem and we’re not affiliated with them. We work on Rheem equipment because Enterprise has a lot of it, and we’ve learned where the brand’s specific failure points show up in Clark County heat.

Key Takeaways

  • Most Rheem heat pump part failures in Enterprise show up as a capacitor, contactor, defrost board or reversing valve solenoid.
  • Installed part replacement typically runs $150 – $650 depending on the component and whether OEM or quality aftermarket.
  • Capacitors and contactors are the cheapest, most common fixes. Reversing valves and boards cost more.
  • We don’t carry parts on a truck. The part gets matched to your model number, then sourced and installed.
  • Ray tests the capacitor before anyone says the word compressor.

Which Rheem Models This Applies To

Rheem heat pumps show up in Enterprise in a few common families: the RP series (RP14, RP15, RP16, RP17), the RPKA and RPRL lines, and the older RQ and RPQL units still running in garages and second homes around the valley. The part you need depends on which family and which serial number run, because Rheem changed capacitor specs and control board layouts between generations even within the same series name.

The single most useful thing you can do before calling is photograph the data plate on the outdoor unit. It’s a silver or white sticker, usually on the side or near the service panel, and it lists the model number, serial number, and the factory charge. That plate tells us which run capacitor, contactor and defrost board your unit takes without guessing. Model number alone isn’t always enough; the serial number narrows the production batch, and Rheem did swap components mid-run.

On the OEM vs. aftermarket question: for capacitors we use quality aftermarket equivalents from established manufacturers, and they hold up in Enterprise heat as well as OEM at a lower price. For control boards and reversing valve solenoids we lean OEM because the pinouts and coil specs have to match exactly, and a mismatched board on a Rheem can create intermittent faults that are miserable to chase. If you want OEM for everything, tell us and we’ll quote it. We won’t quietly substitute.

Explore

Styles & brands we work with

  • AC repair
  • Furnace & heating
  • Heat pumps
  • Ductless mini splits
  • Carrier
  • Trane
  • Goodman

Signs Your Rheem Heat Pump Service Is Failing

Heat pumps fail in patterns. Here’s what we see most often on Rheem units in Enterprise and what each symptom usually points to.

  • Outdoor unit hums but the fan won’t spin. Nine times out of ten it’s a failed run capacitor. The compressor may still try to start, which is why you hear the hum, but without the cap doing its job the motor can’t get moving. Left alone, this cooks the compressor.
  • Breaker trips on startup, or the unit shuts off after a few minutes. A failing contactor or a shorted capacitor can cause this. We’ve also seen it from a weak compressor winding, which is why we test before we quote.
  • Heat pump runs but doesn’t heat or cool properly in either mode. On a Rheem, this often tracks back to the reversing valve or its solenoid coil. If the valve won’t shift, you’re stuck in one mode. The solenoid is the cheaper fix; the valve body is a bigger job.
  • Unit ices up in heating mode and won’t defrost. Defrost board or defrost sensor failure. Enterprise winters are mild, but the defrost cycle still runs, and a failed board will let the coil freeze over and stall the system.
  • Thermostat calls, nothing happens at all. Could be a low-voltage transformer, a blown board fuse, or a control board failure. On older Rheem RQ units the transformer is a known wear item.

One reality check specific to Enterprise: the summer heat here shortens capacitor life. We routinely replace caps on Rheem units every 5 to 7 years in this climate, and the ones that fail earliest are usually the ones sitting in direct afternoon sun with poor airflow around the condenser. Shade and a clean coil buy you years.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed part replacement on a Rheem heat pump in Enterprise usually falls between $150 and $650. Here’s what drives the number.

  • Run capacitor replacement: $150 – $280 installed. Includes the cap, testing the motor and compressor windings, and verifying amp draw after.
  • Contactor replacement: $180 – $320 installed. Pitted contacts are the usual cause; we check the control circuit before swapping.
  • Defrost board or sensor: $280 – $480 installed. OEM board pricing moves the range up.
  • Reversing valve solenoid coil: $220 – $400 installed. If the valve body itself has failed, that’s a separate and larger repair, and we’ll tell you honestly whether it’s worth it on the age of the unit.
  • Low-voltage transformer or board fuse: $150 – $300 installed.

Those ranges are for repair work. If the diagnosis points to a full system replacement rather than a part swap, AC installation in Enterprise runs $3,500 – $7,500 depending on tonnage, efficiency tier and whether the line set needs replacing. We’ll give you a written number either way, and the Free Second Opinion on any written estimate stands if you’ve got one from someone else.

Every repair carries the 90-Day Done Right Promise in writing. If it’s not right, one call brings Ray back. No trip charge inside the county for Enterprise addresses.

DIY or Call Us?

Some of this is safe to check yourself. Some of it isn’t, and we’d rather say so plainly.

Safe to check: the outdoor unit’s data plate for the model and serial numbers, whether the breaker has tripped, whether the disconnect is pulled, and whether the condenser coil is visibly clogged with cottonwood or dust. You can also look at the capacitor for a bulged top or leaking residue without touching the terminals. Photograph all of it and call us with the pictures.

Not safe: anything involving the inside of the electrical panel on the unit. A heat pump capacitor holds a charge after the power is off, and it can knock you flat. The contactor and control board sit on live 240-volt circuits. Reversing valve and refrigerant work requires EPA certification and gauges. This isn’t a warning we throw around to sell jobs; it’s the part of the work where people get hurt. We’d rather you call.

The middle ground: if you’re not sure what failed but you’ve got the model number and a symptom, call (844) 455-2034. Ray will tell you over the phone whether it’s worth a visit or something you can safely eyeball yourself first. Estimates are free.

FAQs

Need HVAC help nationwide? Licensed & insured · 1-hour response · free estimates
Call (844) 455-2034
Local Service Coverage

Request a Free Estimate in Enterprise

Tell us what you need - Ray's Heating & Air Enterprise responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch