Heat pumps
AC repair
Furnace & heating
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateGoodman Heat Pump Service: The Enterprise Owner’s Guide
Goodman heat pump service in Enterprise usually means one of a few known parts has quit – a run capacitor, a contactor, a defrost board, a reversing valve, or a fan motor – and the installed repair runs $150 – $650 for most jobs, with same-day availability on common failures. We work on Goodman units across Enterprise and know their habits. You’ll usually find out the hard way: the house won’t cool on a 108-degree afternoon, or the system runs nonstop and never satisfies the thermostat. Maybe the outdoor unit hums and won’t start, or you hear a click and then nothing. In Enterprise, the tell is often the shoulder season swing – a warm February day where the unit flips into cooling and reveals a capacitor that has been quietly drifting out of spec all winter.
Key Takeaways
- Most Goodman heat pump part failures in Enterprise are diagnosed and repaired the same day.
- Typical installed repair lands at $150 – $650 – we test the small parts before anyone talks about the big ones.
- We service Goodman plus Carrier, Trane, and Lennox, and we’re an independent shop, not affiliated with Goodman.
- Readings first, numbers second: you see the meter readings and the price before any work starts.
Which Goodman Models This Applies To
Goodman heat pumps show up around Enterprise in three broad families: the GSZ14 and GSZ16 single-stage and two-stage split systems, the GSXC18 and GSZC18 inverter-driven units, and the packaged GPH series. The indoor side is usually an ARUF or ASPT air handler matched to the outdoor unit. Goodman built a lot of these, and the parts inside them – capacitors, contactors, defrost control boards, fan motors, reversing valves – follow generational patterns. An older GSZ13 and a newer GSZ14 may share a capacitor value but not a board, and the inverter units take a completely different control board than the single-stage boxes most homeowners picture.
To identify the right part, we read the model and serial plate on the outdoor unit – usually on the side panel behind the service valves – and cross it to the correct spec. Goodman has a habit of running several capacitor microfarad ratings and voltage ratings across near-identical cabinets, so guessing by sight is how wrong parts get installed. The label tells the truth. Once we have the model, the choice is OEM versus a quality aftermarket equivalent. For Goodman specifically, OEM boards and motors are the safe call on the inverter and communicating units, while capacitors, contactors, and fan motors have well-made aftermarket equivalents that hold up fine and cost less. We tell you which is which and why, and you decide.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Signs Your Goodman Heat Pump Service Is Failing
Here’s what a failing part actually looks like from your side of the thermostat.
- Outdoor fan won’t spin, or spins slow. Usually a failed run capacitor or a seized fan motor. A bulged or leaking capacitor is the classic culprit, and it’s a cheap test before anyone mentions a motor.
- Unit clicks and hums but won’t start. Often a pitted contactor or a low-pressure switch doing its job. The contactor’s points burn over years of cycling, and the compressor never gets clean power.
- System ices up in heating mode or never defrosts. A bad defrost control board or a failed sensor. Goodman boards are common enough that we keep the test procedure memorized.
- Heat pump cools in summer but won’t heat, or heats but won’t cool. A stuck or failed reversing valve – the part that flips the system between modes. It’s a bigger job, and worth confirming with readings before condemning it.
- Tripped breaker or a burnt smell at the outdoor unit. Worn wiring, a shorted compressor winding, or a failing contactor. Stop running it and call – this is not one to ride out.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed part repairs in Enterprise land in these ranges. The number you see is the number you pay – parts plus labor, tested and confirmed before we leave.
- Run or start capacitor: $150 – $280 installed.
- Contactor: $180 – $320 installed.
- Defrost control board: $280 – $520 installed.
- Outdoor fan motor: $320 – $650 installed.
- Reversing valve: quoted after diagnosis – the larger jobs push toward the top of the $150 – $650 repair range and sometimes beyond, and we tell you upfront which side you’re on.
What drives the range: the part itself, whether it’s OEM or a quality equivalent, and how much labor the swap takes. Inverter and communicating Goodman units take more diagnostic time and pricier boards than the single-stage boxes. Every repair comes with the 90-Day Done Right Promise in writing – if it’s not done right, one call brings Ray back. Readings first, numbers second. You see both before we start.
DIY or Call Us?
Some things you can safely check yourself. Others, you shouldn’t touch.
Safe to check: the breaker at the panel, the filter, the thermostat batteries, and whether the outdoor unit is clear of debris. That’s where DIY stops being a good idea. A heat pump’s capacitor holds a charge even after you kill power at the breaker – it can knock you flat, and plenty of homeowners have found that out the hard way. The contactor and control board sit in the same live cabinet. The reversing valve means brazing refrigerant lines under pressure, which is a licensed job, full stop. If you’re not trained on a meter and don’t know which terminals to discharge, this is a call-a-pro job and no shame in it.
When you’re ready, we answer the phone live – day or night. Call (844) 455-2034 for a free estimate and we’ll get you on the schedule.
FAQs
Capacitors are the short-lived ones – expect 5 to 10 years in Enterprise’s heat, and shorter on units that run hard through July and August. Contactors and fan motors typically give 10 to 15 years. Boards and reversing valves often outlast the rest of the system if the unit isn’t stressed. The 108-degree summers here work every part harder than a milder climate would, so we don’t promise the book number – we test what’s actually in front of us.
Sometimes, but rarely worth it. A pitted contactor can be dressed up, a capacitor can’t be repaired at all, and a board with a blown relay is a replace. We test first and tell you honestly whether a repair buys you real time or just delays the inevitable. If a replacement part is the right call, the numbers are in front of you before we touch anything.
A capacitor or contactor is usually 30 to 60 minutes on site once we’ve confirmed the diagnosis. A board or fan motor runs an hour or two. A reversing valve is a half-day job because the refrigerant has to be recovered, the valve brazed in, and the system recharged and tested. Most Enterprise repairs are done the same day we diagnose them.
From Goodman distributors and quality aftermarket suppliers that stock the right spec for your model. We read your model plate, order the correct part number, and don’t sub in a near-match. If a part has to be ordered, we tell you the lead time upfront so you’re not guessing. No parts sit on a truck – we bring the right one for the job.
Ray’s Heating & Air Enterprise is an independent service provider and is not affiliated with Goodman. We also service Carrier, Trane, and Lennox systems. Questions about a Goodman part or a system that’s acting up? Call (844) 455-2034 for a free estimate – Ray answers his own phone, and the person at your door is the one who’ll be back if anything needs a second look.
Written by the team at Ray’s Heating & Air Enterprise, serving Enterprise and nearby areas.